QQ在线
产品介绍
OVERVIEW
The ZigBee Pro Gateway enhances the original ZigBee Gateway, which allows Mio Modero R-4 and R-3 Remotes the ability to wirelessly communicate with NetLinx Controllers and control connected system devices. ZigBee Pro is an ideal solution for retrofit projects where control wires cannot be run and for installations such as Government or Bank Buildings, where 802.11 security concerns prevent it from being used. ZigBee Pro Repeaters are also available to extend ZigBee coverage throughout a building.
FEATURES
◆ Improved Range and Greater Roaming Distance - ZigBee Pro Gateways feature 6dB of improved sensitivity which translates to up to 65 additional feet of range (actual performance can vary based on the environment).
◆ Supports Third Party Devices – While Mio R-3 and R-4 Remotes are currently the only AMX-supported ZigBee Pro devices, the ZigBee Pro Gateway will be able to communicate with third party ZigBee Pro devices in the future.
◆ Encrypted for Security - All wireless communications on ZigBee Pro are encrypted, further protecting user data and ZigBee Pro utilizes the 802.15.4 protocol, offering an alternative to 802.11.
◆ Onboard Diagnostic Tool With Signal Strength - A convenient diagnostic tool is included which can display signal strength and latency directly on Mio R-4s and R-3s to assist with installation and troubleshooting to determine the best location for Gateways and Repeaters.
SPECIFICATIONS
DIMENSIONS (HWD)
4 1/2" x 2 1/2" x 15/16" (11.43 cm x 6.35 cm x 2.38 cm)
Note: depth does not include antenna
WEIGHT
◆ Without Antenna: 5.6 oz (158.75 g)
◆ With Antenna: 6.4 oz (181.44 g)
POWER
◆ 10.5 - 18 VDC; (13.5 VDC nominal operation voltage)
◆ Power over Ethernet (PoE) Class 2
MEMORY
◆ 16 MB of FLASH
◆ 16 MB of SDRAM
RADIO SPECIFICATIONS
◆ Frequency: 2.4 GHz
◆ Operating Channels: 11 – 26
◆ Modulation Technique: DSS
◆ Output Power: Region/country specific
◆ Coverage Area: 165 feet (50.2 m)
FIRMWARE/SOFTWARE SPECIFICATIONS
◆ Management: Built-in browser-based management with User Name/Password authentication
◆ IP Configuration: Static IP or DHCP client (default is DHCP/Zeroconf)
◆ Communications: ZigBee, TCP/IP
FRONT COMPONENTS
◆ LEDs
○ PWR/STATUS: Blinking green LED: the device is installed and communicating properly. Power ON, but no master connection, is indicated with a solid light, Power OFF is indicated with no light.
○ LAN: Green LED: Ethernet connection is established. Blinking: indicates both sending and receiving information via Ethernet.
○ RF: Solid LED: end devices are connected; no LED: end devices not connected; LED blinks to indicate activity.
◆ Antenna Mount: A reverse SMA connection that supports a 2.4GHz antenna.
◆ ID Button: When used in conjunction with NetLinx Studio, sets the device and system numbers for the NXR-ZGW-PRO. Press and hold for approximately 30 seconds to return the NXR-ZGW-PRO to factory default settings.
REAR COMPONENTS
◆ Power Connector: 2-pin 3.5mm captive-wire connector
◆ Power Over Ethernet (PoE) - Powers the device through the CAT5 cable. Both Power and Data can be transmitted simultaneous through the CAT5 cable when using the appropriate equipment.
◆ Ethernet Port: 10/100BaseT Modular (RJ-45) connector - connects the NXR-ZGW-PRO to your LAN.
ENVIRONMENTAL
◆ Operating Temperature: -30ºC (-22ºF) to 70ºC (158ºF)
◆ Relative Humidity: 5% to 85% non-condensing; intended for indoor use only)
CERTIFICATIONS
FCC ID: CWU-NXRZGWPRO, IC: 5078B-ZGWPRO, CE, IEC-60950-1, Japan Approval, ZigBee Certified
INCLUDED ACCESSORIES
◆ Rubber feet
◆ Velcro mounting strip
◆ 2.4GHZ, MONO, RSMA, 3.5IN, 2.0DBI Antenna (70-0012-SA)
◆ Power Supply (24-5791-SA)
