产品介绍
精巧的外型设计及卓越的声音还原能力,Microflex界面话筒是会议室理想的选择方案。具有可编程功能、无声薄膜开关、可互换话筒头、逻辑输入和输出以及LED指示灯等特性,Microflex界面话筒在各种应用场合都能够提供高品质声音。
■ 心型、超心型及无指向性
■ 黑色或白色型号可供选择
■ 可编程、无声薄膜开关
■ 逻辑输入和输出端子
■ LED指示灯
提供型号:
MX391W C/S/O 白色,串联前置放大器,配有具有4-pin mini接头的电缆
C=心型,S=超心型,O=无指向性
- Polar Pattern
- Cardioid (MX391/C, MX391W/C, MX391LP/C, MX391WLP/C)
- Supercardioid (MX391/S, MX391W/S, MX391LP/S, MX391WLP/S)
- Omnidirectional (MX391/O, MX391W/O, MX391LP/O, MX391WLP/O)
- Supercardioid (MX391/S, MX391W/S, MX391LP/S, MX391WLP/S)
- Environmental Requirements
- Operating Temperature Range: -18 to 57 degrees C (0 to 135 degrees F)
- Relative Humidity: 0 to 95%
- Dimensions
- See User Guide
- These specifications apply only to the MX391/MX391W microphones when used with the supplied preamplifier. All measurements taken with the microphone mounted on a 76.2 cm x 76.2 cm (30 in. x 30 in.) wooden surface and with the sound source incident at 30 . with respect to the surface plane.
- Frequency Response
- 50 to 17,000 Hz
- Output Impedance (at 1000 Hz)
- 180 ohms actual (rated at 150 ohms)
- Open Circuit Sensitivity 1 kHz ref. 1 V per Pascal *
- Cardioid: -29.6 dB (33.5 mV)
- Supercardioid: -28.3 dB (38.5 mV)
- Omnidirectional: -21.5 dB (81.4 mV)
- All settings -12 dB at 0 gain; *1 Pascal = 94 dB SPL
- Supercardioid: -28.3 dB (38.5 mV)
- Maximum Sound Pressure Level (1 kHz at 1% Total Harmonic Distortion, 1 k ohm load)
- Cardioid: 118.8 dB
- Supercardioid: 117.5 dB
- Omnidirectional: 110.7 dB
- All settings +6 dB at 0 gain
- Supercardioid: 117.5 dB
- Signal to Noise Ratio (referenced at 94 dB SPL)
- Cardioid: 71.4 dB
- Supercardioid: 72.7 dB
- Omnidirectional: 79.5 dB
- Supercardioid: 72.7 dB
- Equivalent Output Noise (A-weighted)
- Cardioid: 22.6 dB SPL
- Supercardioid: 21.3 dB SPL
- Omnidirectional: 14.5 dB SPL
- Supercardioid: 21.3 dB SPL
- Dynamic Range at 1 k ohm Load
- 96.2 dB
- 100 dB at 0 gain
- Common Mode Rejection
- 45 dB minimum, 10 Hz to 100 kHz
- Preamplifier Output Clipping Level
- -6 dBV (0.5 V)
- 12 dB at 0 gain
- Polarity
- Positive sound pressure on diaphragm produces positive voltage on pin 2 relative to pin 3 of the preamplifier XLR output connector.
- Power Requirements
- 11 to 52 Vdc phantom
- 2.0 mA current consumption